品牌德国莱克LIK品牌 | 有效期至长期有效 | 最后更新2018-11-06 07:59 |
德国莱克品牌0.5-1000 | 碳钢 铸铁、铸钢、不锈钢低温度达-200℃ | |
浏览次数866 |
进口不锈钢电磁阀|德国莱克LIK品牌-德国莱克阀门
德国莱克LIK品牌,进口不锈钢电磁阀是工业过程自动化控制系统用执行器。它在接受电控信号后能自动开启或关闭,实现对管道中的液体介质的通断或流量调节控制。
进口不锈钢电磁阀应用范围
广泛地应用于纺织、印刷、化工、塑料、橡胶、制药、食品、建材、机械、电器、表面处理等生产和科研部门以及浴室、食堂、空调等人们日常生活设施中
本阀为分步动作直接导式常闭电磁阀,线圈通电后衔铁先带动小阀开启,大阀在所形成的介质压差和电磁力的作用下而开启。线圈断电,衔铁部件复位,大小阀利用介质压力而紧密关闭。
进口不锈钢电磁阀参数说明
型号规格:DN1~DN200
适用压力:0.02~160MPa
适用介质:气体、液体
介质温度:-200~+350℃
介质粘度:小于50CSt(大于时需定制)
防护性能:IP65
阀门材质:304、316 、316SS、316L
控制方式:常开、常闭
电源电压:DC12~127V AC24~380V
连接方式:内螺纹、外螺纹、焊接、法兰(适用压力5MPa以下)
泄 漏 量:零
进口不锈钢电磁阀备注特殊要求可定制安装尺寸根据所需要产品,用传真方式或电话告知.
进口不锈钢电磁阀工作原理
常闭:当线圈通电时,电磁铁芯吸合,卸压孔打开,主活塞由介质压力推动,
打开主阀口,介质流通。
当线圈断电时,主阀口关闭,介质截止。
常开:当线圈通电时,电磁铁芯吸合,卸压孔打闭,主活塞由介质压力推动,
关闭主阀口,介质截止。
当线圈断电时,主阀口打开,介质流通。
进口活塞式电磁阀结构特点
活塞式电磁阀在我们生活中运用广泛,产品种类也较为丰富: 化工专用电磁、 231Y三通电磁阀、二位三通电磁阀、进口脉冲除尘电磁阀、RSDF系列带过滤网大口径喷泉电磁阀(先导式)、进口燃气紧急切断电磁阀、进口耐腐蚀塑料王电磁阀、ZCLD超低温电磁阀、ZCA真空电磁阀、m型浇封防爆电磁阀、LIKTRER出口系列微型电磁阀阀等,接下来,我们就简单对其特点进行分析。
1.电磁阀阀芯均为不锈钢材料、活塞式结构,抗动作疲劳性强。
2.活塞环设计结构更有科学性,采用特殊材料制造,不会被介质中的杂质卡死。
3.动作密封性能高、寿命长。
4.金属活塞与金属阀腔不产生直接摩擦,不会被卡住,阀体的安装方向无限制。
5.专制线圈,线圈不易烧毁。
6.合理的密封材料和结构,密封性能更好。
7.长期停止动作后重新启动,动作同样灵敏。
8.接口尺寸通常为国家或国际标准,客户可定制特殊接口。
9.使用常规产品寿命长达700万次以上。
10.一种具有外套型密封活塞环和具有高性能组合型密封活塞环的电磁阀。
11.工作压力高达200MPa的超高压电磁阀。
进口不锈钢电磁阀广泛地应用于纺织、印刷、化工、塑料、橡胶、 制药、食品、建材、机械、电器、表面处理等生产和科研部门以及 人们日常生活设施中。所以对于保养问题也是不容忽视的,不锈钢 电磁阀使用保养如下:
1、不锈钢电磁阀安装后,须通入介质试动作数次,确认正常后方可 投入正式使用。
2、应定期清洗大阀内外及衔铁吸合面的污物。注意不要损坏密封面 。
3、工作时,要注意阀门前后压力表,要求工作压力不得超过额定压 力,工作压差必须在额定压差范围内。当工作压力超过额定压力或 工作压差超过额定压差时,不锈钢电磁阀要停止使用,关闭前后手 动阀,以防止电磁阀爆炸和泄漏。
4、不锈钢电磁阀从管路上卸下不用时,应将内部零件试净并用压缩 空气吹净储存。
5、使用时间较长时,如活塞与阀座间密封不好,可将活塞密封面重 新磨平,再和阀座研磨。
6、不锈钢电磁阀较长时间不用时,应关闭阀前手动阀,重新启用时 ,蒸汽电磁阀应将冷凝水排除干净,并作试动作数次,待开关正常 后方可投入使用。
译文:
Stainless steel solenoid valve of the six maintenance knowledge:
Stainless steel solenoid valve widely used in textile, printing, chemical, plastic, rubber, pharmaceutical, food, building materials, machinery, electrical appliances, surface treatment and other production and scientific research departments and facilities in People's Daily life. So for the maintenance problem also nots allow to ignore, stainless steel solenoid valve use maintenance is as follows:
1, stainless steel solenoid valve is installed, you must pass into the medium to try several times, confirmed rear can put into normal use.
2, should be cleaned regularly big valve inside and outside, and on the surface of the armature and dirt. Be careful not to damage the sealing surface.
3, work, must pay attention to the valve before and after the pressure gauge, working pressure shall not exceed the rated pressure, working pressure difference must be within the rated pressure difference. When working pressure over the rated pressure or differential pressure over the rated pressure difference, stainless steel solenoid valve to stop using manual valve before and after the closing, in order to prevent the electromagnetic valve explosion and leakage.
4, stainless steel solenoid valve need not when, from the internal parts shall be stored try clean with compressed air blowing off.
5, use for a long time, such as the seal between the piston and valve seat is bad, the piston sealing surface can be smooth again, again and seat grinding.
6, stainless steel solenoid valve for a long time need not when, the valve should be closed before the manual valve, restart, the electromagnetic valve of steam condensed water should be ruled out clean, and try several times, to switch to normal rear can put into use.